如何将VNX Unify恢复到可以用VIA做初始化的状态-联想乐享知识库

如何将VNX Unify恢复到可以用VIA做初始化的状态 问题:磁盘分区 故障现象: VNX Unified系列在用VIA做File部分初始化的时候，只能做一次，如果配置一半的时候失败或者关闭了VIA的窗口，VIA就无法再次扫描到该存储。解决方案: 1、使用Putty等软件通过串口线登录CS0，注意这里的串口线必须是随机自带的串口线，因为CS的接口特别窄，其他串口线会无法插入。串口速率19200 a)、串口登录CS0 用户名：root 密码：nasadmin 注意：如果存储是双CS配置的话，可以先把CS1给关闭，拔掉线缆，然后配置完成VIA之后，再把CS1添加上，或者按照下面的方法来设置双CS配置。 b)、从CS前面板的标签中记录下CS0和CS1的 eth3的MAC地址，或是运行以下命令来查看MAC地址并记录eth3的IP： # /sbin/ifconfig eth3 2、运行命令： # /nasmcd/sbin/clariion_mgmt -info 如果返回： Error 12: Not configured 说明proxy ARP没有配置，可以直接跳到步骤3。如果Proxy ARP已经配置，运行以下命令来将SP的ip恢复到出厂设置： # /nasmcd/sbin/clariion_mgmt -stop 返回信息： Checking if running as root...yes Checking if model is supported...yes Checking for integrated system...yes Checking if interface eth3 is configured...yes Checking if SP (10.241.168.206) is up...yes Checking if SP (10.241.168.207) is up...yes Step 1/12 [28185788417]: Changing SPA IP address. Changing SPA IP from 10.241.168.206 to 128.221.252.200 (subnetmask 255.255.255.0, gateway 128.221.252.104) Step 2/12 [28185788421]: Waiting for SPA to restart. Waiting for SPA to go down.....done (19 secs) Step 3/12 [28185788425]: Waiting for ping response from SPA. Waiting for 128.221.252.200 to respond...done (2 secs) Step 4/12 [28185788427]: Waiting for CLARiiON software to start on SPA. Waiting for CLARiiON software to start on SPA...done (61 secs) Waiting until SPB sees 128.221.252.200 in the domain...done (4 secs) Step 5/12 [28185788429]: Updating NAS database with SPA IP address. Adding rules to allow outbound traffic from SPB Updating SYMAPI database with new CLARiiON IP addresses...done (33 secs) Step 6/12 [28185788433]: Removing Proxy ARP for SPA on Control Station Removing host specific route for SPA Removing rules that allow outbound traffic from SPA Removing ARP entry for SPA Updating /etc/hosts entry for SPA Step 7/12 [28185788418]: Changing SPB IP address. Changing SPB IP from 10.241.168.207 to 128.221.253.201 (subnetmask 255.255.255.0, gateway 128.221.253.104) Step 8/12 [28185788422]: Waiting for SPB to restart. Waiting for SPB to go down.....done (18 secs) Step 9/12 [28185788426]: Waiting for ping response from SPB. Waiting for 128.221.253.201 to respond.....done (14 secs) Step 10/12 [28185788428]: Waiting for CLARiiON software to start on SPB. Waiting for CLARiiON software to start on SPB...done (37 secs) Waiting until SPA sees 128.221.253.201 in the domain...done (2 secs) Step 11/12 [28185788430]: Updating NAS database with SPB IP address. Updating SYMAPI database with new CLARiiON IP addresses...done (20 secs) Step 12/12 [28185788434]: Removing Proxy ARP for SPB on Control Station Removing host specific route for SPB Removing rules that allow outbound traffic from SPB Removing ARP entry for SPB Updating /etc/hosts entry for SPB FINISH: Operation took a total time of 4 minutes 35 seconds to complete. 3、运行以下命令来检查 /etc/rc3.d下是否存在” S95cable_check”文件： # cd /etc/rc3.d # ls -la S95cable_check 4、如果该文件存在，可直接跳至下一步。如果该文件不存在并且之前也没有保留备份的话，那么你需要从对应版本的NAS光盘中来提取这个文件，并通过WinSCP等软件将文件传输到存储上。 文件在光盘的路径